Hotline & Consultation
in 57 categories
Last updated on:
Tuesday, October 10, 2017
Bathroom accessories: System Pfosten 16 V2A stainless steel towel holder for bath.
Award winner 2003
Towel holder made of V2A-stainless steel, system Pfosten 16, for bath
Design towel holder with stainless steel tube Ø 16mm, bracket system Pfosten 16, 2 modifications, 4 standard lengths or acc. to measurements
shower curtain rods
Towel holder made of V2A-stainless steel Pfosten 16Bathroom accessory by Stahldeko: towel holder Pfosten 16 combines classic style with functionality, as complete set in single-rail modification, incl. mounitng material. Consists of stainless steel rod Ø 16mm, brackets Pfosten 16/short in side closed modification, optionally with or without base plate. Simple mounting with 1-point fixing. With the help of middle brackets, joints and wall bracket can be extended to towel holder in L-shape and U-shape.
Towel holder bracket Pfosten 16/short: modifications and mounting system
Side closed modification can be used as bracket and finial at the same time
|Bracket system Pfosten 16/short: rod bracket with and without base plate (Fig. left open modification)|
|Mounting system Pfosten 16/short: with and without base plate (Fig. open modification)|
|Mounting system: extension (50mm) for bracket Pfosten16/short (Fig. open modification)|
Application examples and expansion examples:
Towel holder Pfosten 16, Ø 16mm
Towel holder Pfosten 16, L-shaped, inside corner solution for bathroom: You need stainless steel rods Ø 16mm according to measurements, a joint made of stainless steel Ø 16mm, bracket Pfosten 16/short in side open and closed modification with or without base plate. Due to movable joint, the towel holder angle is variable from 75° up to 285°
Bathroom accessory: towel holder Pfosten 16, L-shaped, outside solution: You need stainless steel rod Ø 16mm according to measurements, one stainless steel joint Ø 16mm, 2 brackets Pfosten 16/short side open and 2 closed with or without base plate. The towel holder angle is variable from 75° up to 285°, due to movable joint.
U-shaped towel holder decoration for outside corner: It requires two joints (G) with variable angle of 75 ° to 285 °. Conclusion is possible with closed-makers or wall bearings. Following the same principle, the inner corner solution is realized.
Decorate inside corner in the bathroom or shower, towel holder in the trapezoidal-shape: Thanks to the joint motion Stahldeko-towel holder for each wall angles are appropriate, whether external or inside corner.
|description:||Towel holder made of stainless steel V2A system Pfosten 16|
(depending on modification):
|V2A - stainless steel 18/10, DIN WNR 1.4301, inox, heat resistant, impact resistant, easy to clean|
|Machining:||high accuracy machining with CNC-automatic lathe|
|Surface:||polished surfaces, very good optical homogeneity, Particle distribution 240, optically raised|
|Suitable:||for bath, kitchen, shower and bathroom|
|Modification:||complete 1-rail towel holder|
|Bracket system:||bracket Pfosten16/short side closed|
|end knob:||Stainless steel bracket Pfosten 16 at the same time, as finial|
(depending on the modification):
|1-point fixing with bolts and Spax-screws, drill holes and screws are covered with base plate, wall or ceiling mounting|
|Lengths:||Other lengths on request, 30, 40, 50 and 60 cm|
|Accessory:||additionally supplied: bracket, rings, hooks, joints, rod bracket extensions, tie-back, tubes, wall bracket|
Here are some examples of the form of curved towel rails and rods:
|rod for towels in S-shaped bend||Towel - Bar full circle||towel holder as a semi-circle curved||quarter circle and segment - for bending Holder||curved towel bar||semicircle with straight extensions turn|
|square-bend for Towel - Bar||U-shape curved rods for towels||L-shaped curved towel holder||holder as a bow with straight extension||towel Any angle bend||trapezoidal curved towel bar|